2025年9月8日月曜日

スキーの寿命を守るチューン — 必要十分な研磨と9月のTODO

9月に入ってモリモリと作業しております。

こちらの板は、他店様でチューンされてから当方へご依頼いただいたものですが、ここまでソールが薄くなるとリペアもソールの切り貼りもできなくなります。ソールの厚みは1.2から1.4mmが多いです。フラットにこだわるあまりガシガシ削ると、数回でチューン不能となります。

フラット研磨といっても、削れるのはたかだかこの1mmの範囲です。スノーボードはフラットなど無理というのはおわかり頂けると思います。その場合は歪みを計測しながら、手仕上げでエッジの角度を調整します(手仕上げコースのみ)。

レーシング板であれば短期決戦なので板の寿命を考えずに削ればよいのですが、フリーライド・BC板はできるだけ長く使いたいですよね。うちは「いい塩梅」「必要十分」で削り、神経質にリペアしたりフラットにこだわりすぎたりしません。ジャンルに合わせて最適なチューンをしています。

Todo更新:チューン依頼を9月中に完了。土蔵工房の補修・整備、新工房の使用契約、テスト板製作、テンプレート更新、デザイン・印刷部屋の整備、屋根裏工房修理、WEB・デジタルの整備、ツアーやゲストルーム、経営、スクール・ワークショップ、チューン工房の作業も進めます。

Facebookの元投稿 ・ HAPPY TUNE ホームページ


Tuning to Protect a Ski’s Lifespan — Just Enough Grinding and September To-Dos

I’ve been busy with all kinds of work since September began.

This ski came to me after being tuned elsewhere. When the base gets this thin, repairs and base patches are no longer possible. Most ski bases are about 1.2 to 1.4 mm thick. If you grind aggressively in pursuit of perfect flatness, the ski may become impossible to tune after only a few services.

Even with flat grinding, there is only about 1 mm of material to work with. As you can see, a snowboard cannot realistically be perfectly flat. In such cases, I measure the distortion and adjust the edge angles by hand (available only in the hand-finished course).

For racing skis, you might grind without worrying about lifespan because the goal is a short campaign. But freeride and backcountry skis should last as long as possible. We aim for a good balance and what is genuinely necessary. We don’t over-repair or obsess over flatness. We tune each ski for its discipline.

September to-dos include completing current tuning orders, workshop repairs, test skis and templates, improvements to the design and printing room, web and digital work, tours, guest rooms, business planning, workshops, and tuning-room upgrades.

Original Facebook post ・ HAPPY TUNE website

0 件のコメント:

コメントを投稿

「めっちゃ板走って、また出しに来ました!」|スノーボードチューンナップ

2026年9月22日 「めっちゃ板走って、また出しに来ました!」 今日、お客さんからそう言ってもらえて、めちゃ嬉しかったと同時に安心しましたです。 うちには、スノーボード用の「ストーンマシン」がありません。サンディングマシーンという機械で研磨します。 ス...